C32 ACERT Tier 3 Standard Equipment

• AIR INLET SYSTEM
  • Separate Circuit After-Cooled (SCAC)
  • Seawater After-Cooling (SWAC) System
  • Air cleaner
  • Turbochargers, jacket water cooled
  • Turbochargers inlet, 152 mm (6 in) OD straight connection

• CONTROL SYSTEM
  • Programmable Low Idle (550 - 750 rpm)
  • WOSR (Wide Operating Speed Range) available for - A, B, & C Ratings
  • Programmable High Idle Limit for WOSR Ratings
  • Electronic diagnostics and fault logging
  • Engine and transmission monitoring (speed, temperature, pressure)
  • Electronic fuel/air ratio control
  • Engine Protection Mode for extended ambient conditions
  • Torque Limiting functionality for WOSR ratings only
  • 70-pin customer connector
  • Throttle Input signal options

• COOLING SYSTEM
  • Separate Circuit After-Cooling (SCAC) for Heat Exchanged (HEX) & Keel cooled engines
  • Jacket Water (JW) and SCAC Heat Exchangers Shell & Tube for HEX cooled engines
  • SCAC pump, gear driven
  • Jacket water pump, gear driven
  • Sea water pump, bronze impeller, gear driven, for HEX cooled engines only
  • Sea water Pump & JW Heat Exchanger Connection: 76.2 mm (3in) ID Standard
  • Keel Connections: 76.2 mm (3in) ID Standard 4 Bolt ANSI Flange Connection
  • SCAC and JW shunt tanks for maintaining proper pump inlet pressures
  • Seawater After-Cooling (SWAC) System

• EXHAUST SYSTEM
  • 4 Bolt 130 mm (5.12 in) diameter flanged outlet
  • Water-cooled exhaust manifold & turbocharger

• FLYWHEELS & FLYWHEEL HOUSINGS
  • SAE standard rotation (CCW facing exciter end)
  • Flywheel Housing: SAE No. 0, Flywheel: 18 inch, 136 teeth

• FUEL SYSTEM
  • Duplex Fuel Filters, Spin-on, RH & LH service
  • Fuel connections size:Supply JIC 37 Deg -10 (7/8-14), Return JIC 37 Deg -8 (3/4-16)
  • Plate Type Fuel Cooler installed behind Aftercooler Shunt Tank
  • Fuel transfer pump, gear driven
  • Manual fuel priming pump
  • Hybrid fuel line design

• LUBE SYSTEM
  • Simplex Oil Filters, RH or LH service
  • Deep sump oil pan
  • RH or LH service oil filler locations
  • RH or LH service dipstick
  • Oil pump, gear driven

• MOUNTING SYSTEM
  • Front support - adjustable

• POWER TAKE-OFFS
  • Front Poly-V groove pulley (Quantity 1) for auxiliary drives

• GENERAL
  • Common electrical bonding point
  • Engine does not ship with zinc components

C32 ACERT Tier 3 Optional Equipment

• Air Inlet Systems
  • Air Inlet Cleaner
  • Air Inlet Adapter

• Charging Systems
  • Battery Charger
  • Charging Alternators
  • Ammeter

• Cooling System
  • Marine Gear/Transmission Oil Coolers
  • Connections

• Exhaust System
  • Dual Elbow
  • Flexible Fitting
  • Dual Muffler
  • Muffler Spark Arresting
  • Flange

• Fuel System
  • Water Separator

• Instrumentation
  • OEM Wiring Harness
  • Engine to Engine Harness
  • Instrument Panels
  • Exhaust Temperature Sensors
  • Wiring Harness
  • Gauges
  • Transmission Sensors

• Lube System
  • Transmission Oil Cooler
  • Manual Sump Pump
  • Duplex Oil Filters

• Protection System
  • Fuel and Oil Shielding

• Starting System
  • Air Starting Motor
  • Air Start Accessories
  • Electric Starting Motors - Single 24 Volt
  • Starting Aids
  • Battery Sets - 24 Volt - Dry
  • Dual Starting Motors (Electric and Air)

• Packing
  • Engine Protective Cover
  • Export Packing
  • Storage Preservation

• Mounting System
  • Front Support
  • Adapter Kits
  • Isolator Mounts

• Power Take-Offs
  • Front Enclosed Clutches
  • Rear Hydraulic Pump Drive

• GENERAL
  • Fumes Disposal

• CONTROL SYSTEM
  • Instrument Panels
  • CATERPILLAR ALARM AND PROTECTION
  • Fuel and Oil Shielding