Reversing contractor and pushbutton switch with cable
Electronic speed setting equipment with actuator and speed pick-up
Emergency shutdown equipment with pushbutton, separate, for manual emergency stop
Engine Indicators
Gauge board with set liquid damped pressure gauges for: fuel, lubricating oil, fresh water, starting air, and charge air.
On-engine thermometers for fuel, lubricating oil, fresh water, and charge air
Electric remote speed indicator
Turbocharger and remote speed indicator
Exhaust gas temperature indicator
Control
Manual control on engine, including: control panel with start /stop key, speed setting device, mechanical shutdown device, change over of control functions from engine to remote control
Starting solenoid valve on engine, 24 V DC
Separate electronic speed governor
Monitoring for Unattended Operation
Pressure switches, mounted on engine, for: - Lube oil pressure at full load below danger level - Low lube oil pressure - Lube oil pressure below danger level - Lube oil pressure prelubrication failed - Low fresh water pressure at engine inlet - Fresh water pressure at engine inlet below danger level - Low fresh water pressure in LT circuit - Low starting air pressure - Low control air pressure engine/shutdown air pressure - Low fuel pressure at engine inlet Switches for: - High lube oil temperature at engine inlet - Lube oil temperature at engine inlet above danger level - High water temperature at engine inlet - Water temperature at engine outlet above danger level - High charge-air temperature at engine inlet - Detection of water in charge-air duct - Leak fuel level - Alarm contact for high differential pressure at fuel filter - Alarm contact for high differential pressure at lube oil back flushing filter - Set of thermocouples after each cylinder, before and after turbocharger - Crankcase oil mist detector Control Cabinet with housings for wall mounting, including: - Protection equipment designed for automatic and manual stop input signals, starting interlock input signals, monitoring for the wire break of the input signal units and the emergency shutdown solenoid - Speed recording system for overspeed, firing speed and minimum speed - Start /stop logic, controlled by engine automatic start (optional) - Service hour counter - Optional Noris alarm system, cassette type, designed for alarm inputs for the engine including exhaust mean-value monitoring equipment as well as alarm inputs for the propulsion plant - Optional Group alarm panel for the bridge and with optional and acoustic alarm equipment
Starting Air System
Separate non-return valve for the starting air pipe to the engine
Air Intake System
Air intake filter, fitted on the turbocharger
Air bottles, separate
Diesel Oil System
Circulating pump fitted on engine
Duplex filter with differential pressure indication
Exhaust System
Turbocharger at free end with transition nozzle (0 degrees from the vertical and away from engine), with compressor cleaning device
Expansion joint separate
Separate silencer and spark arrester, unlagged 35 dB(A)
Fresh Cooling Water System
HT pump, fitted on engine
HT pump, fitted on engine
HT thermostat, not powered and separate
Engine preheating equipment, fitted on base frame
Lubricating Oil System
Plate cooler, fitted on engine
Force pump, fitted on engine
Prelubrication pump, fitted on base frame, electric motor driven
Plate cooler, fitted on engine - Force pump, fitted on engine - Prelubrication pump, fitted on base frame, electric motor driven - Boll and Kirch automatic backflushing filter, fitted on engine
Pressure control valve, fitted on engine
Connecting Parts - Engine
Set of connecting parts between flange coupling and flywheel
Flexible flange coupling between engine and generator
Base frame with flywheel guard and incorporating lube oil sump tank, for engine and generator
Mounting of engine and generator on the base frame
Set of bonded rubber rails for resilient mounting of the base frame
Set of flexible pipe connections
Tools
Set of tools for the engine including hydraulic tightening tools and nozzle tester
Set of tools for turbocharger
Inside micrometer for cylinder liners
Ruler for cylinder liner
Spare Parts
Set of engine spare parts for unrestricted operation
Set of spare flexible pipe connections
Specifications
Minimum Rating
1310 ekW1640 kV·A
Maximum Rating
1460 ekW1830 kV·A
Emissions
IMO Tier II
Aspiration
Turbocharged-Aftercooled
Bore
200 mm7.87 in
Displacement
75 l4589 in³
Engine Control
Electronic
Generator Set Control
Electronic
Stroke
300 mm11.81 in
Weight
23100 kg50926 lb
Height
3389 mm174.7 in
Length
6798 mm267.6 in
Width
1816 mm99.8 in
Equipment
8CM20C Standard Equipment
Engine
Motor-driven barring gear, fitted on engine
Reversing contractor and pushbutton switch with cable
Electronic speed setting equipment with actuator and speed pick-up
Emergency shutdown equipment with pushbutton, separate, for manual emergency stop
Engine Indicators
Gauge board with set liquid damped pressure gauges for: fuel, lubricating oil, fresh water, starting air, and charge air.
On-engine thermometers for fuel, lubricating oil, fresh water, and charge air
Electric remote speed indicator
Turbocharger and remote speed indicator
Exhaust gas temperature indicator
Control
Manual control on engine, including: control panel with start /stop key, speed setting device, mechanical shutdown device, change over of control functions from engine to remote control
Starting solenoid valve on engine, 24 V DC
Separate electronic speed governor
Monitoring for Unattended Operation
Pressure switches, mounted on engine, for: - Lube oil pressure at full load below danger level - Low lube oil pressure - Lube oil pressure below danger level - Lube oil pressure prelubrication failed - Low fresh water pressure at engine inlet - Fresh water pressure at engine inlet below danger level - Low fresh water pressure in LT circuit - Low starting air pressure - Low control air pressure engine/shutdown air pressure - Low fuel pressure at engine inlet Switches for: - High lube oil temperature at engine inlet - Lube oil temperature at engine inlet above danger level - High water temperature at engine inlet - Water temperature at engine outlet above danger level - High charge-air temperature at engine inlet - Detection of water in charge-air duct - Leak fuel level - Alarm contact for high differential pressure at fuel filter - Alarm contact for high differential pressure at lube oil back flushing filter - Set of thermocouples after each cylinder, before and after turbocharger - Crankcase oil mist detector Control Cabinet with housings for wall mounting, including: - Protection equipment designed for automatic and manual stop input signals, starting interlock input signals, monitoring for the wire break of the input signal units and the emergency shutdown solenoid - Speed recording system for overspeed, firing speed and minimum speed - Start /stop logic, controlled by engine automatic start (optional) - Service hour counter - Optional Noris alarm system, cassette type, designed for alarm inputs for the engine including exhaust mean-value monitoring equipment as well as alarm inputs for the propulsion plant - Optional Group alarm panel for the bridge and with optional and acoustic alarm equipment
Starting Air System
Separate non-return valve for the starting air pipe to the engine
Air Intake System
Air intake filter, fitted on the turbocharger
Air bottles, separate
Diesel Oil System
Circulating pump fitted on engine
Duplex filter with differential pressure indication
Exhaust System
Turbocharger at free end with transition nozzle (0 degrees from the vertical and away from engine), with compressor cleaning device
Expansion joint separate
Separate silencer and spark arrester, unlagged 35 dB(A)
Fresh Cooling Water System
HT pump, fitted on engine
HT pump, fitted on engine
HT thermostat, not powered and separate
Engine preheating equipment, fitted on base frame
Lubricating Oil System
Plate cooler, fitted on engine
Force pump, fitted on engine
Prelubrication pump, fitted on base frame, electric motor driven
Plate cooler, fitted on engine - Force pump, fitted on engine - Prelubrication pump, fitted on base frame, electric motor driven - Boll and Kirch automatic backflushing filter, fitted on engine
Pressure control valve, fitted on engine
Connecting Parts - Engine
Set of connecting parts between flange coupling and flywheel
Flexible flange coupling between engine and generator
Base frame with flywheel guard and incorporating lube oil sump tank, for engine and generator
Mounting of engine and generator on the base frame
Set of bonded rubber rails for resilient mounting of the base frame
Set of flexible pipe connections
Tools
Set of tools for the engine including hydraulic tightening tools and nozzle tester
Set of tools for turbocharger
Inside micrometer for cylinder liners
Ruler for cylinder liner
Spare Parts
Set of engine spare parts for unrestricted operation